I measured the temperature of the flanges where some of the electronics will go and I found that the RGA flange was at 55C and the two full range gauges were at 65C. I also stopped bake 9 to cool down for measurement.

1. Turn off the RGA filament and disconnect it.

2. Record the pressure and then close the angle valve and gate valve on the RGA line to isolate it from the system.

3. Turn off the backing and turbo pump and let the turbo pump spin to a stop by slowly leaking the chamber. The slower the safer.

4.Slowly open the vents on the chamber and the turbo pump. Making sure not to raise the pressure too fast.

5. Once done venting the chamber, open the lid by removing the bolts and prying the lid open with a long flat head screw driver.

6. Removed previous parts and placed them into clean bags. Place new parts inside of the chamber and group them together close to the center.

7. Place the lid back onto the chamber and tighten the bolts in a circular pattern until tightened all the way with the wrench.

8. Make sure all vents are closed and turn the backing pump back on.

9. The turbo pump can be turned back on when the pressure reaches e-1 torr.

10. Wait until the chamber reaches a pressure of e-6 torr before opening the angle and gate valve on the RGA line. After the RGA line is open and the pressure is still below e-6 torr, the RGA filament can be turned on and a leak test of the lid should be performed.

11. After the leak test shows no leaks, proceed with starting the low temp bake.

Below is the procedure we will follow to assemble the FROSTI prototype.

1. Install SS guide rods and bottom Macor spacers in bottom reflector
2. Install AlN elements on top of bottom Macor spacers
3. Install upper Macor spacers on top of AlN elements
4. Feed unterminated power and RTD leads through slots in upper reflector
5. Install upper reflector, using guide rods to slowly lower into position
6. Install vented SS bolts for reflectors; Macor bolts for heater elements
7. Remove SS guide rods
8. Bundle power and sensing cable with PEEK cable ties and SS cable mounts
9. Terminate power and sensing cable bundles with PEEK DB25M connectors

[Jon, Tyler, Shane, Luis]

On Wednesday we completed the migration of the electronics workshop from 1119 to the large new workbenches in 1129. The two workstations pictured closest to the front of the room are for electronics assembly and testing, while the two in the rear will house LIGO CDS workstations. We moved all of the tools, cabling, and soldering and test equipment from 1119 to this new location. We also moved the large tool chest to 1129, as pictured, and moved the smaller tool chest to 1119 in its place.

The electronics workbench is ready for use. 

cleaning cleanroom and particle count

• 12:30 pm: ran zero count test on particle counter
• 12:32 pm: started particle count.
  • zone 3:
    • 0.3 u: 59,488
    • 0.5 u: 9561
    • 1.0 u: 706
• zone 4:
  • 0.3 u: 7732
  • 0.5 u: 1912
  • 1.0 u: 290

NOTE: Frame ceiling tile collapsed in cleanroom, explaining insanely high 0.3 u particle count in zone 3 (nearly 6 times above limit). Wiped down tile and put it back in ceiling frame.

• 12:56 pm: began surface check and wipedown, including softwalls
• 1:16 pm: started vacuuming the floor
• 1:32 pm: finished vacuuming the floor
• 1:33 pm: started mopping the floor
• 1:47 pm: finished mopping the floor
• 1:48 pm: started cleaning the buckets
• 1:53 pm: started mopping with IPA wipes
• 2:05 pm: finished mopping with IPA wipes
• 2:06 pm: changed sticky floor mats
• 1:53 pm: started particle count
  • zone 3:
    • 0.3 u: 6401
    • 0.5 u: 3450
    • 1.0 u: 1787
• zone 4:
  • 0.3 u: 4073
  • 0.5 u: 2452
  • 1.0 u: 1039

Took some RGA data of the chamber after it has been cooling down. I do not believe that this data accurately shows the HC levels in the chamber as the pressure is still above where it was at before the bake and was still falling. I believe more time is needed to let the pressure fall and for the RGA filament to remain on to return to a point where the data can be trusted.

Turned off the heating tape today in anticipation to take more RGA data on Sunday or Monday morning before the meeting.

Came into the lab in the morning to check on the chamber heating. I decided to set the PID controllers to 110C rather than 120C as the chamber lid and wall were reading near 140C. With the PID controllers at 110C the chamber lid and wall now read 126C and 132C. Currently the PID controllers are placed on the cross in front of the RGA and the reducing nipple in front of the turbo pump. I believe this is a good equilibrium and will leave the tape on until Saturday when it will be turned off to cool down.

The workbenches are now completely assembled and put into their final places. Additionally, the tool chest has been moved.

After the bake is done on Saturday it will be cooled down and RGA data will be taken to measure the out gassing rate of the stainless steel fasteners inside the chamber. Then on Tuesday we will plan to vent and open the chamber again to put the macor inside and repeat the another low temp bake and then test the macor early in week 11. Then the next material will be the aluminum mounting hardware for mounting the heaters and that should hopefully be done before the end of week 11 so the heaters can be tested afterwards after being cleaned with vector alpha wipes.

The tabletops have been attached to the workbench frames. Unfortunately, one of the tabletops came out of the box with a large scratch and small dent in the middle. One of the electric top shelves is ready to be attached to the undamaged table, but the other is yet to be opened. Assembly will be completed Wednesday morning.

Update: I was able to put the FROSTI power controller on the lab network. It is connected to the switch in the top of the rack and is assigned a static IP address of 192.168.1.12 and an NDS hostname of relay1.

The controller can be remotely accessed through an SSH command line interface as well as an HTML webpage, which can be opened from any web browser on the lab network by navigating to the above IP address (the login credentials are the same as for the workstation computers).

There is also an unofficial Python package for interfacing with the controller: dlipower. We will investigate using this package to interface the controller with soft EPICS channels hosted on the CyMAC. This will allow us to create a custom MEDM screen for controlling the FROSTI heater elements.

Edit: The login credentials were set up to be the same as for the CDS workstations.

Luis and Aiden vented the chamber today. We closed off the RGA section and then proceeded to open the the vent on the main body after turning off the turbo and backing pump. We then opened the lid and placed in all the stainless steel hardware that will be used in evaluating the FROSTI optics and heater elements. We also inspected the weldments before closing it up. Check the clean and bake data base where there is now a new section outlining the parts in each test. We then closed the lid, tightened the bolts, turned the backing pump back on and let the pressure drop until it was below 1e-1 torr. Then turned the turbo pump back on and after a few hours the pressure was back down to 4.16e-7 torr. The RGA was turned off during all of this and was turned back on when done even though we closed both valves to keep the RGA volume under vacuum.

[Tyler, Shane, Mohak, Cynthia, Luke, Michael, Luis]

[Aiden, Luis]

Tested every weld and flange to find leaks. Only found that the flange on the turbo pump and reducing nipple was still at 2e-9 torr on the leak. The chamber still rose in pressure when the two gate valves were closed but no noticeable leak could be found on the lid or welds.

Below are a basic diagram of what the RTD measurement circuit logically looks like and an example schematic of the actual wiring. The schematic wiring will be placed internally into a chassis, connected to the RTDs via DB25 cable.

cleaning cleanroom and particle count

• 3:37 pm: started particle count
  • zone 3:
    • 0.3 u: 1205
    • 0.5 u: 748
    • 1.0 u: 249
• zone 4:
  • 0.3 u: 1496
  • 0.5 u: 748
  • 1.0 u: 290
• 3:57 pm: began surface check and wipedown, including softwalls. NOTE: vacuum chamber insulation crumbling at edges, dropping loose flakes. Scatters residue whenever jostled, so wiping it down just releases more. Not enough flakes are being released for it to be a major issue, but definitely something to keep an eye on.
• 4:18 pm: started vacuuming the floor
• 4:29 pm: finished vacuuming the floor
• 4:30 pm: started mopping the floor
• 4:35 pm: finished mopping the floor
• 4:36 pm: started cleaning the buckets
• 4:41 pm: started mopping with IPA wipes
• 4:52 pm: finished mopping with IPA wipes
• 4:52 pm: changed sticky floor mats
• 4:53 pm: started particle count
  • zone 3:
    • 0.3 u: 3367
    • 0.5 u: 1787
    • 1.0 u: 914
• zone 4:
  • 0.3 u: 1039
  • 0.5 u: 498
  • 1.0 u: 249

As a follow up ELOG 261, I have received advice from one of the vacuum experts at LIGO Hanford on best practices for our RGA:

1. For future RGA degassing, definitely keep the main volume isolated, since it could contaminate the main volume with everything that just got cooked off of the filament. So the procedure should be to (i) close both gate valves, (ii) ensure the angle valve on the bypass line is open, (iii) initiate the degas cycle on the RGA, (iv) pump the RGA volume through the bypass line, until its pressure returns to its pre-degas level.

2. Repeated degassing of the filament will definitely wear it down much faster, so do this operation sparingly.

3. As long as the pressure of the RGA volume is in the UHV range (~1e-9 torr), best practice is to leave the filament on. This keeps it hot which helps prevent particulate from settling on it. However the electron multiplier should stay off when not actively taking scans, as it will wear down if left on all the time.

[Jon, Shane, Luis]

My repair of the internal ribbon connecting the ADC to the adapter board resolved the timing signal problem. After this repair, we were able to start the front-end IOP model and checked out the RTS diagnostic screens (pictured below). All indicator lights were green except for the DK flag (indicating the DAC outputs are not enabled) and the DAQ flag (indicating that the system is recording data to disk). Those were both as expected, because the DAQD data acquisition service was not set up yet and the DAC outputs are not enabled until at least one user model (which outputs signals to the DAC) is started. I created and installed a simple user model (C1MSC) and confirmed that the DK flag clears once this model starts.

I later attempted to set up the DAQD service, which is needed to save data, but am yet to successfully debug it. I have received some guidance from one of LIGO's CDS experts and will try it at my next opportunity for lab work.

After initial analysis from last week on a single RTD, I then extended to looking at all 8 in series with R_ref (set to 1 kOhm). Shown below are the edge cases for the setup:

• RTDs are all at ambient lab temperature. This would correspond to a minimum resistance value.
• RTDs all read out 400 C. This gives the maximum resistance value.

The results show that indeed only a few mA of current is drawn even at room temperature (a little above 5.5 mA), and this will continue to decrease with increasing temperature. The voltage across a single terminal, at a maximum, is only about 5.4 V.

1. Run a second RGA degas cycle, but next time with the main volume valved off with only the RGA volume being pumped (through the bypass line). This will prevent "boiled off" particulate from entering the main chamber and will also increase the pumping rate for the RGA volume, reducing the amount of particulate that resettles on the RGA filament.
   
   
2. I also noticed that the SRS manual states that the filament is designed to be long-lived and it is recommended to leave it on any time the RGA is on. By leaving the filament on all the time (i.e., hot), we could reduce the amount of particulate that is evidently settling on it between scans. I am checking whether LIGO Lab does this in their own chambers.

cleaning cleanroom and particle count

• 12:30 pm: Tyler and Aiden started organizing cables in cleanroom
• 12:35 pm: started particle count in flow bench
• 0.3 u: 11681
• 0.5 u: 3284
• 1.0 u: 1039
• 12:50 pm: started cleanroom particle count
  • zone 3:
    • 0.3 u: 14549
    • 0.5 u: 10351
    • 1.0 u: 6194
• zone 4:
  • 0.3 u: 10808
  • 0.5 u: 4655
  • 1.0 u: 1953
• 1:07 pm: began surface check and wipedown, including softwalls
• 1:19 pm: started vacuuming the floor
• 1:28 pm: finished vacuuming the floor
• 1:29 pm: started mopping the floor
• 1:33 pm: finished mopping the floor
• 1:34 pm: started cleaning the buckets
• 1:37 pm: started mopping with IPA wipes
• 1:39 pm: finished mopping with IPA wipes
• 1:40 pm: changed sticky floor mats
• 1:41 pm: started particle count
  • zone 3:
    • 0.3 u: 8397
    • 0.5 u: 5071
    • 1.0 u: 2618
• zone 4:
  • 0.3 u: 6651
  • 0.5 u: 4323
  • 1.0 u: 2120

[Jon, Tyler, Shane, Peter, Luis]

Today we completed the first phase of lab clean-up. Activities included:

• CF/KF parts stored under the cleanroom table were removed and transferred to Physics 1129
• Cleanroom workbench cleared, with all FROSTI hardware collected into one of the large SS bins
• High surfaces outside the cleanroom (lights, table enclosure frames, rack, cabinets) wiped down with IPA wipes
• Floor HEPA-vacuumed outside the cleanroom
• Sticky mats changed throughout the lab

Tomorrow, we will complete turn-over of the cleanroom (HEPA vacuuming of floors, mopping of floors, IPA wiping of softwalls and work surfaces). Shane will post a forthcoming measurement of the cleanroom particulate levels, post-turnover.

Preliminary RTD calculations are shown below, given an input of 10 V and desiring a few mA of current. It looks like R_ref should be at least 1 kOhm (refer to plots/circuit below), keeping in mind we need to have <10 V input for the ADC.

RP: The Red Pitaya Software was updated to OS 2.00. All examples on the RP website should run without issue.

• Topmost Sorensen: +24V (reserved for FROSTI)
  • Positive terminal:
  • unconnected for now
  • Negative terminal: [negative terminal is grounded]
  • jumper to Sorensen ground screw
• Sorensen 2nd from the top: +18V
  • Positive terminal:
  • white power cable wire for AA chassis
  • white power cable wire for AI chassis
  • white power cable wire for BI chassis
  • white power cable wire for BO chassis
  • Negative terminal: [negative terminal is grounded]
  • jumper to Sorensen ground screw
  • black power cable wire for AA chassis
  • black power cable wire for AI chassis
  • black power cable wire for BI chassis
  • black power cable wire for BO chassis
• Sorensen 3rd from the top: -18V
  • Positive terminal:[positive terminal is grounded]
  • jumper to Sorensen ground screw
  • green power cable wire for BI chassis
  • green power cable wire for BO chassis
  • Negative terminal:
  • green power cable wire for AA chassis
  • green power cable wire for AI chassis
• Bottommost Sorensen: +6V
  • Positive terminal:
  • white power cabe wire for timing chassis
  • Negative terminal: [negative terminal is grounded]
  • jumper to Sorensen ground screw
  • green power cable wire for timing chassis
  • black power cable wire for timing chassis

FLIR: After some adjustments, the plot generated from the FLIR measurements look much more symmetric (see attachment). There are more included grid points, which smooths out the curve as compared to last week.

Red Pitaya: It looks like a new OS update was released for the RP, which includes a new Python API (was previously only available in C). I'm going to try and update the one we have currently running in lab.

By 5:30 pm Friday, the pressure had reached 8.6e-8 torr and was continuing to fall. So it seems we are OK to proceed with permanentizing this configuration (cable routing, heater tape reinstallation).