Action items for facilities

• Ceiling lights replacement
• Fume hood cleaned and refurbished
• Sink countertop cleaning
• Floor cleaned and waxed
•  

Below are slides discussing RIN infrastructural updates related to the CyMAC.

Slides

Below are slides giving an update on RH O6 design progress.

These are the frequency averaged and veto binned plots for the initial Red Pitaya and CyMAC systems.

Updated CyMAC measurement, comparing 260 hrs of measurement time vs. 405 hrs.

[Ma, Tyler, Christina]

This past week, we were able to set up the data streaming for continuous acquisition to the PCs, and can conduct the initial tests now. We were able to do this by:

• Installing the correct OS ecosystems to each Red Pitaya
• Installing the terminal streaming client
• Debugging formatting and file saving issues by saving the data in a TDMS file on the host PC.

Date and Time: Around 4:20 PM on Auguest 6, 2025

Location and Temperature:

• Back of the room 1119, around the working station: 90.2 °F
• Front of the room 1119, around the doorway: 85.8 °F
• Back of the room 1129, around the working station: 93.4 °F
• Front of the room 1119, around the doorway: 82.3 °F
• In the hallway in front of room 1119: 77.2 °F

Simulating how point absorber defects on Advanced LIGO mirrors affect cavity performance by modeling a 4km LIGO-like arm cavity with a point absorber fixed at 5cm off-center on the ITM. In this simulation, displaced the laser beam across a 21×21 grid while calculating the deformation, then measuring the resulting power loss in the cavity (~283W circulating power).

[Tyler, Ma, Christina, Maple, Cece, Mary, Pooyan, Audrey]

We started by cleaning outside of the cleanroom wiping down the cable channel and working our way down while taking the pre-cleaning measurement. We then stated wiping down the inside of clean room and vacuumed, mopped the outside of the cleanroom. Finally, we vacuumed, mopped, and wiped down the floor inside the cleanroom.

Particle Count Measurements:

• Pre-cleaning (2:00 pm):
  • Zone 3:
    • 0.3 µm: 2707
    • 0.5 µm: 1374
    • 1.0 µm: 249
  • Zone 4:
    • 0.3 µm: 2207
    • 0.5 µm: 1166
    • 1.0 µm: 374

• Post-cleaning (4:30 pm):
  • Zone 3:
    • 0.3 µm: 4082
    • 0.5 µm: 2415
    • 1.0 µm: 708
  • Zone 4:
    • 0.3 µm: 1707
    • 0.5 µm: 791
    • 1.0 µm: 416

[Ma, Christina, Tyler]

ADC CyMAC 260 hr, 8192Hz sampling rate channels V3 and Vref6

[Ma, Christina, Tyler]

Figure 1 shows the following PSDs for channels 0-15 from the 14 hour test. Figure 2 shows the reduced chi squared and CSD plots for both the 2 Hz and 16 Hz resolutions.

Date and Time: Around 4:50 PM on July 1, 2025

Location and Temperature:

• Back of the room 1119, around the working station: 85.7 °F
• Front of the room 1119, around the doorway: 83.5 °F
• Back of the room 1129, around the working station: 79.1 °F
• In the hallway in front of room 1119: 76.5 °F

[Christina, Ma, Tyler]

Yesterday, Ma and I started taking data for the PSD/CSD measurements while the photodetectors and one of the heater elements are on (8) and are using the Red Pitaya to compare it to the data we took for the same measurements on the CyMAC. It will be finished Wednesday morning, and then we plan on starting to take additional recordings in order to conduct the same type of comparison for the dark noise measurements.

I've been looking into the performances of individual channels on the Cymac by computing their individual PSDs and corresponding CSDs that show their noise relation to each other. It appears some channels do have lower noise floors than others, and some combinations of these actually do perform similar to the Red Pitaya (showing below the CSD between CHs 3 and 5), although it doesn't look like it's much of an improvement. The best method as of now still appears to be phase-locking two separate ADCs to reduce the correlated noise floor further.

This can be further discussed at the July 22, 2025 group meeting.

[Luke, Luis]

We’ve been looking into methods for evaluating the performance of the HEPA filters in the clean room. Measuring flow rate appears to be a promising approach, since the filter manual specifies a recommended minimum of 70 ft/min.

At the moment, we don’t have a flow rate measurement device on hand. We're currently looking into two options:

• A standard vane-style anemometer, which is more affordable but may lack sensitivity near the minimum required flow rate.
• A hot-wire anemometer, which offers better resolution and accuracy at lower speeds, though it's more expensive.

In the next few days, either Luis or I will contact Terra Universal to see if they have any measurement solutions that would integrate well with our clean room setup, or if they can recommend best practices for verifying HEPA performance.

[Christina, Ma, Tyler]

Pomona Box completed and is now on the server rack in 1119. Additionally, the photodetectors were connected to the box and set up in front of the heater elements.

Below is attached the ADC noise floor of two CyMAC channels vs the Red Pitaya.

The frequency resolution of these RIN spectra are 16 Hz, with N_meas = 19,308,426 for the CyMAC, and N_meas = 263,024.

After acquiring some new equipment for the labs, a few of us spent time on Thursday and Friday sorting through everything and storing them into their appropriate places. New vacuum parts, power supplies, cables, and much more were included. The rooms are now ready for the lab tours commencing Tuesday afternoon.

Below are the drawings for the pomona box modifications

Slides

Slides