Using the configuration in section 2.11.1 in the Sorensen installation and operation manual (attached below), I'm able to remote control the Sorensen power supply.

I use DAC VEXC8 as the external voltage source and a breakout board to match the configuration of connector J3.

I have recorded 7 cycles (attached below), and am now working on analyzing the data.

We currently have the parts for a DB9 connector but need parts for a DB25 connector, where did we get the parts for the DB9 connector? We may be able to use the same company for the DB25 connector.

Also need a cable for the connectors. Find a DB9 to DB9 cable in 1129, not sure if I can disassemble it and use just the cable.

The pressure in the vacuum chamber rises to 2.12e-8 torr, which needs baking.

Date and Time: Around 3:50 PM on June 2, 2025

Location and Temperature:

• Back of the room 1119, around the working station: 86 °F
• Front of the room 1119, around the doorway: 84.1 °F
• Back of the room 1129, around the working station: 78.6 °F
• Front of the room 1129, around the doorway: 78.3 °F
• In the hallway in front of room 1119: 75.2 °F

By measuring the resistance of the ladder, I obtained a graph of resistance as a function of voltage.
All the heater elements behave consistently, showing only a small standard deviation.
However, heater element 5 shows a significantly larger standard deviation.
Upon examining the initial ladder graph, I noticed that the resistance of heater element 5 increases following a power outage that resets the system.
At this point, I am unsure why this behavior occurs.

CYMAC Remote Control Cable Assembly

Cable Functions

The custom cable assembly serves two primary functions:

Note: All connections are verified with a multimeter.

Note: This cable allows remote control of the Sorensen power supply with an external voltage source (Cymac DAC).

Note: For more details, check section 2.11.1 from the attached Sorensen power supply manual.

Slides

[Christina, Ma, Tyler]

Pomona Box completed and is now on the server rack in 1119. Additionally, the photodetectors were connected to the box and set up in front of the heater elements.

[Christina, Ma, Tyler]

Yesterday, Ma and I started taking data for the PSD/CSD measurements while the photodetectors and one of the heater elements are on (8) and are using the Red Pitaya to compare it to the data we took for the same measurements on the CyMAC. It will be finished Wednesday morning, and then we plan on starting to take additional recordings in order to conduct the same type of comparison for the dark noise measurements.

Date and Time: Around 4:50 PM on July 1, 2025

Location and Temperature:

• Back of the room 1119, around the working station: 85.7 °F
• Front of the room 1119, around the doorway: 83.5 °F
• Back of the room 1129, around the working station: 79.1 °F
• In the hallway in front of room 1119: 76.5 °F

[Ma, Christina, Tyler]

Figure 1 shows the following PSDs for channels 0-15 from the 14 hour test. Figure 2 shows the reduced chi squared and CSD plots for both the 2 Hz and 16 Hz resolutions.

[Tyler, Ma, Christina, Maple, Cece, Mary, Pooyan, Audrey]

We started by cleaning outside of the cleanroom wiping down the cable channel and working our way down while taking the pre-cleaning measurement. We then stated wiping down the inside of clean room and vacuumed, mopped the outside of the cleanroom. Finally, we vacuumed, mopped, and wiped down the floor inside the cleanroom.

Particle Count Measurements:

• Pre-cleaning (2:00 pm):
  • Zone 3:
    • 0.3 µm: 2707
    • 0.5 µm: 1374
    • 1.0 µm: 249
  • Zone 4:
    • 0.3 µm: 2207
    • 0.5 µm: 1166
    • 1.0 µm: 374

• Post-cleaning (4:30 pm):
  • Zone 3:
    • 0.3 µm: 4082
    • 0.5 µm: 2415
    • 1.0 µm: 708
  • Zone 4:
    • 0.3 µm: 1707
    • 0.5 µm: 791
    • 1.0 µm: 416

Date and Time: Around 4:20 PM on Auguest 6, 2025

Location and Temperature:

• Back of the room 1119, around the working station: 90.2 °F
• Front of the room 1119, around the doorway: 85.8 °F
• Back of the room 1129, around the working station: 93.4 °F
• Front of the room 1119, around the doorway: 82.3 °F
• In the hallway in front of room 1119: 77.2 °F