Today I installed the second desktop workstation in 1129. The new machine is an Intel NUC13ANHi5, with a 12-Core Intel i5-1340P CPU, 32GB DDR4 RAM, and a 1TB SSD.

I loaded it with a fresh installation of Debian 12 and installed the LIGO CDS workstation (control room) tools. It is assigned the hostname ws4 and and the static IP address 192.168.1.19 on the local lab network. Like the other CDS workstations, there is just one user account accessible with the usual credentials.

The machine is fully set up and ready for use.

One ongoing work is to make all lab machines automatically backed-up on Scribe on a daily basis. The updates should be boatable and stored for some time (potentially a few weeks) on Scribe. Making whole disk images has already been tried for some of the machines with no problems. (e.g., Cymac and WorkStations)

The same thing can not be done with Chimay though, as it currently has one huge RAID-controlled volume that stores all the information (OS, home directories, and NDS-downloaded data). Creating daily full disk images of such a system is not practical. 

Here is the plan we came up with to overcome this issue:

1. Create one full disk image of Chimay and store it on Scribe (it was already done)
2. Move the nds-downloaded raw data temporarily to Scribe and remove it from Chimay
3. Make another full disk image of Chimay
4. Burn this image to a single disk and boot chimay with it

5. Restore the rest of Chimay disks and move the NDS data back

    

On the weekend (Sat and Sun 9/7-8) I tried to execute these steps. There wasn't enough free space left on Scribe to move all the NDS data to it, so I stored part of this data temporarily on WS4. Then I also checked storage-consuming directories and, in one case, removed some non-important stored files. As there was no free space left on Scribe to execute step no. 3, I initiated storing the image on WS3. Unfortunately, a couple of different trials of the image-creation process failed as there was not enough free space on WS3 to accommodate Chiamy image as well. I was not able to reduce the image size such that it can be stored on WS3. 

These are the options left for us to get this work done. 

1. Distribute the NDS files between different machines to make enough free space on Scribe for the image and then follow the previous plan
2. Shrink the Chimay drive size, create the image and then follow the previous plan
3. Temporarily transfer some services to Megatrone (Network gateway, Wiki, elog) and recreate chimay and its services from scratch

• Hosted Lukes model on Chimay. It's available at https://richardsonlab.ucr.edu/real-time-frosti
• The sourcecode is at Github. It is clones at /var/www/html/real-time-frosti, and this is the block added to nginx config file at /etc/nginx/sites-available/default :
  
  location /real-time-frosti {

root /var/www/html;
index index.html index.htm index.php;
}
• Also added this line to the crontab, so the code will be checked for updated from the sourcecode every five minutes. 
  
  */5 * * * * cd /var/www/html/real-time-frosti/ && git pull 
  
  
• TODO: Move the sourcecode from Github to git.ligo.org, and make the repository public. 

Port 80 is kept closed by default. This might be causing the certbot auto-renewal cronjob to fail. Therefore we must renew the certificate manually.

Step 1: Open port 80. (This is needed as the certificate renewal process runs some tests which requires client communication over port 80)

Step 2: Run the following command

sudo certbot certonly --force-renew -d richardsonlab.ucr.edu

Step 3: Confirm the certificate was renewed by running the following command

sudo certbot certificates

Jon, Cao

Today we raised the height of the shelf overhanging the cleanroom laser table by 8 inches. This was done to create more vertical clearance between the top-loading vacuum chamber and the bottom of the shelf. The added clearance should make both removing the chamber lid and inserting large parts easier.

The procedure required unmounting the shelf and removing all eight vertical support posts (1" x 1" x 18.5" pieces of 80/20 unistrut). The support posts were taken to the machine shop and cut, retapped, and cleaned (coarsely, with IPA wipes) prior to reinstallation. We took care to minimize the contamination introduced into the cleanroom, but some amount of particulate from disturbing the shelf was unavoidable.

This work is completed, and the cleanroom is now ready for final cleaning (HEPA vac, mopping, and wiping down of all surfaces including the softwalls).

Jon, Cao

In effort to try to reduce the noise level inside the cleanroom, we have dialed all four HEPA fan-filter units (FFUs) down from HIGH to MEDIUM speed. These dials can only be accessed from inside the cleanroom, by bringing in the large ladder and opening adjacent ceiling tiles.

We tested three configurations, in each case with all the FFUs on either HIGH (initial state), MEDIUM, or LOW. We measured the ambient noise in each configuration.

Going from HIGH to MEDIUM yields the largest improvement, reducing the ambient sound intensity by 6 dB (i.e., by a factor of 4, corresponding to a ~35% reduction in perceived volume).

An additional 3 dB of noise reduction can be achieved by further reducing the fan speeds to LOW. However, even after allowing some extended settling time (few hours), we found the particle counts to be fluctuating right at the threshold zone for ISO Class 5. Thus we dialed the fan speeds back up to MEDIUM with the expectation that this will be sufficient for Class 5 performance.

The cleanroom now needs to be recertified with a fresh round of five-zone particle count measurements.

• pre-cleaning particle counts:
  • zone 3
  • 0.3 mu: 2494
  • 0.5 mu: 748
  • 1.0 mu 124
  • zone 4
  • 0.3 mu: 374
  • 0.5 mu: 41
  • 1.0 mu: 0
• 3:45 pm: Started wiping the surfaces(laser table,chamber, computer) inside the cleaning room.
• 4:05 pm: Finished wiped the surfaces
• 4:08 pm: Began vacuuming cleanroom floor
• 4:28 pm: Finished vacuuming cleanroom floor.
• 4:29 pm: Began mopping the cleanroom floor.
• 5:15 pm: Finished cleanroom clean.
• 6:00 pm: post-cleaning particle counts (full 5 zone measurement) attached below

cleaning cleanroom and particle count

• 12:00 pm: started particle count
  • Zone 3
    • 0.3u: 3533
    • 0.5u: 540
    • 1.0u: 166
  • Zone 4
    • 0.3u: 290
    • 0.5u: 124
    • 1.0u: 41
• 12:31 pm: Started checking the surface inside the cleanroom and began surface wipedown
• 12:50 pm: started vacuuming the floor
• 1:05 pm: Finished vacuuming floor
• 1:09 pm: Started mopping the floor
• 1:21 pm: Finished mopping the floor
• 1:22 pm: Started cleaning the baskets
• 1:25 pm: Started mopping with IPA wipes
• 1:39 pm: Finished mopping with IPA wipes
• 1:41 pm: Changed sticky floor mats
• 1:45 pm: Started particle count
  • Zone 3
    • 0.3u: 2327
    • 0.5u: 581
    • 1.0u: 207
  • Zone 4
    • 0.3u: 1662
    • 0.5u: 374
    • 1.0u: 290

cleaning cleanroom and particle count

• 12:00 pm: started particle count
  • Zone 3:
    0.3 u: 2826
    0.5 u: 457
    1.0 u: 166
  • Zone 4:
    0.3 u: 457
    0.5 u: 83
    1.0 u: 41
• 12:17 pm: began surface check and wipedown. NOTE: found a few ants crawling up the metal table frame and on the desk
• 12:29 pm: started vacuuming the floor
• 12:45 pm: Finished vacuuming the floor
• 12:46 pm: Started mopping the floor
• 12:52 pm: Finished mopping the floor
• 12:55 pm: Started cleaning the buckets
• 1:02 pm: Started mopping with IPA wipes
• 1:11 pm: Finished mopping with IPA wipes
• 1:12 pm: Changed sticky floor mats
• 1:14 pm: started particle count
  • Zone 3:
    0.3 u: 2577
    0.5 u: 457
    1.0 u: 166
  • Zone 4:
    0.3 u: 457
    0.5 u: 41
    1.0 u: 0

cleaning cleanroom and particle count

• 1:10 pm: started particle count
  • Zone 3:
    0.3 u: 2535
    0.5 u: 207
    1.0 u: 41
• Zone 4:
  0.3 u: 789
  0.5 u: 41
  1.0 u: 0
• 1:30 pm: began surface check and wipedown
• 1:41 pm: started vacuuming the floor
• 1:55 pm: finished vacuuming the floor
• 1:57 pm: started mopping the floor
• 2:01 pm: finished mopping the floor
• 2:02 pm: started cleaning the buckets
• 2:08 pm: started mopping with IPA wipes
• 2:17 pm: finished mopping with IPA wipes
• 2:18 pm: changed sticky floor mats
• 2:19 pm: started particle count
  • Zone 3:
    0.3 u: 3990
    0.5 u: 1080
    1.0 u: 374
• Zone 4:
  0.3 u: 540
  0.5 u: 207
  1.0 u: 0

cleaning cleanroom and particle count

• 11:08 am: started particle count
  • zone 3:
    • 0.3 u: 4198
    • 0.5 u: 1080
    • 1.0 u: 581
• zone 4:
  • 0.3 u: 1247
  • 0.5 u: 623
  • 1.0 u: 415
• 11:24 am: break for removal of vac chamber insulation (pictures attached), with counts before removal as seen above, and counts after removal/replacement for zone 3 as follows:
  • zone 3:
    • 0.3 u: 2993
    • 0.5 u: 415
    • 1.0 u: 207
• 12:02 pm: began surface check and wipedown
• 12:13 pm: started vacuuming the floor
• 12:25 pm: finished vacuuming the floor
• 12:26 pm: started mopping the floor
• 12:32 pm: finished mopping the floor
• 12:32 pm: started cleaning the buckets
• 12:37 pm: started mopping with IPA wipes
• 12:43 pm: finished mopping with IPA wipes
• 12:45 pm: changed sticky floor mats
• 12:47 pm: started particle count
  • zone 3:
    • 0.3 u: 2951
    • 0.5 u: 290
    • 1.0 u: 41
• zone 4:
  • 0.3 u: 290
  • 0.5 u: 0
  • 1.0 u: 0

Changed the pre filter inside of the 3 stage HEPA system next to the soldering station. It was rather dirty and I have attached images with a clean filter on the left and the used one on the right. I reset the pre filter age on the system. I tried to see if I could tell if the HEPA filter was dirty but I could not see it. I did not reset the age of the HEPA or UV stations. They are currently 378 days old.

cleaning cleanroom and particle count

• 10:06 am: ran zero count test on particle counter
• 10:07 am: started particle count
  • zone 3:
    • 0.3 u: 2203
    • 0.5 u: 831
    • 1.0 u: 540
• zone 4:
  • 0.3 u: 374
  • 0.5 u: 124
  • 1.0 u: 124
• 10:25 am: began surface check and wipedown
• 10:34 am: started vacuuming the floor
• 10:44 am: finished vacuuming the floor
• 10:45 am: started mopping the floor
• 10:49 am: finished mopping the floor
• 10:50 am: started cleaning the buckets
• 10:57 am: started mopping with IPA wipes
• 11:01 am: finished mopping with IPA wipes
• 11:02 am: changed sticky floor mats
• 11:03 am: started particle count
  • zone 3:
    • 0.3 u: 2535
    • 0.5 u: 374
    • 1.0 u: 166
• zone 4:
  • 0.3 u: 581
  • 0.5 u: 41
  • 1.0 u: 0

cleaning cleanroom and particle count

• 3:16 pm: started particle count.

  NOTE: we are not within the ISO class 5 standard for any size ranges in zone 3. ~6000 above limit in 0.3 u, ~2000 above in 0.5, ~200 above in 1.0

  • zone 3:
    • 0.3 u: 16,711
    • 0.5 u: 5612
    • 1.0 u: 1039
• zone 4:
  • 0.3 u: 6817
  • 0.5 u: 2369
  • 1.0 u: 249
• 3:35 pm: began surface check and wipedown, including softwalls
• 3:50 pm: started vacuuming the floor
• 4:00 pm: finished vacuuming the floor
• 4:01 pm: started mopping the floor
• 4:06 pm: finished mopping the floor
• 4:07 pm: started cleaning the buckets
• 4:08 pm: started mopping with IPA wipes
• 4:14 pm: finished mopping with IPA wipes
• 4:15 pm: changed sticky floor mats
• 4:18 pm: started particle count
  • zone 3:
    • 0.3 u: 23,113
    • 0.5 u: 9686
    • 1.0 u: 1371
• zone 4:
  • 0.3 u: 7191
  • 0.5 u: 2951
  • 1.0 u: 290

cleaning cleanroom and particle count

• 12:30 pm: Tyler and Aiden started organizing cables in cleanroom
• 12:35 pm: started particle count in flow bench
• 0.3 u: 11681
• 0.5 u: 3284
• 1.0 u: 1039
• 12:50 pm: started cleanroom particle count
  • zone 3:
    • 0.3 u: 14549
    • 0.5 u: 10351
    • 1.0 u: 6194
• zone 4:
  • 0.3 u: 10808
  • 0.5 u: 4655
  • 1.0 u: 1953
• 1:07 pm: began surface check and wipedown, including softwalls
• 1:19 pm: started vacuuming the floor
• 1:28 pm: finished vacuuming the floor
• 1:29 pm: started mopping the floor
• 1:33 pm: finished mopping the floor
• 1:34 pm: started cleaning the buckets
• 1:37 pm: started mopping with IPA wipes
• 1:39 pm: finished mopping with IPA wipes
• 1:40 pm: changed sticky floor mats
• 1:41 pm: started particle count
  • zone 3:
    • 0.3 u: 8397
    • 0.5 u: 5071
    • 1.0 u: 2618
• zone 4:
  • 0.3 u: 6651
  • 0.5 u: 4323
  • 1.0 u: 2120

cleaning cleanroom and particle count

• 3:37 pm: started particle count
  • zone 3:
    • 0.3 u: 1205
    • 0.5 u: 748
    • 1.0 u: 249
• zone 4:
  • 0.3 u: 1496
  • 0.5 u: 748
  • 1.0 u: 290
• 3:57 pm: began surface check and wipedown, including softwalls. NOTE: vacuum chamber insulation crumbling at edges, dropping loose flakes. Scatters residue whenever jostled, so wiping it down just releases more. Not enough flakes are being released for it to be a major issue, but definitely something to keep an eye on.
• 4:18 pm: started vacuuming the floor
• 4:29 pm: finished vacuuming the floor
• 4:30 pm: started mopping the floor
• 4:35 pm: finished mopping the floor
• 4:36 pm: started cleaning the buckets
• 4:41 pm: started mopping with IPA wipes
• 4:52 pm: finished mopping with IPA wipes
• 4:52 pm: changed sticky floor mats
• 4:53 pm: started particle count
  • zone 3:
    • 0.3 u: 3367
    • 0.5 u: 1787
    • 1.0 u: 914
• zone 4:
  • 0.3 u: 1039
  • 0.5 u: 498
  • 1.0 u: 249

cleaning cleanroom and particle count

• 12:30 pm: ran zero count test on particle counter
• 12:32 pm: started particle count.
  • zone 3:
    • 0.3 u: 59,488
    • 0.5 u: 9561
    • 1.0 u: 706
• zone 4:
  • 0.3 u: 7732
  • 0.5 u: 1912
  • 1.0 u: 290

NOTE: Frame ceiling tile collapsed in cleanroom, explaining insanely high 0.3 u particle count in zone 3 (nearly 6 times above limit). Wiped down tile and put it back in ceiling frame.

• 12:56 pm: began surface check and wipedown, including softwalls
• 1:16 pm: started vacuuming the floor
• 1:32 pm: finished vacuuming the floor
• 1:33 pm: started mopping the floor
• 1:47 pm: finished mopping the floor
• 1:48 pm: started cleaning the buckets
• 1:53 pm: started mopping with IPA wipes
• 2:05 pm: finished mopping with IPA wipes
• 2:06 pm: changed sticky floor mats
• 1:53 pm: started particle count
  • zone 3:
    • 0.3 u: 6401
    • 0.5 u: 3450
    • 1.0 u: 1787
• zone 4:
  • 0.3 u: 4073
  • 0.5 u: 2452
  • 1.0 u: 1039

cleaning cleanroom and particle count

• 2:03 pm: changed sticky floor mats
• 2:05 pm: started particle count
  • zone 3:
    • 0.3 u: 4863
    • 0.5 u: 1205
    • 1.0 u: 872
• zone 4:
  • 0.3 u: 1953
  • 0.5 u: 789
  • 1.0 u: 457
• 2:35 pm: began surface check and wipedown, including softwalls and ceiling tiles
• 2:45 pm: started vacuuming the floor
• 2:56 pm: finished vacuuming the floor
• 2:57 pm: started mopping the floor
• 3:01 pm: finished mopping the floor
• 3:02 pm: started cleaning the buckets
• 3:05 pm: started mopping with IPA wipes
• 3:08 pm: finished mopping with IPA wipes
• 3:09 pm: started particle count
  • zone 3:
    • 0.3 u: 5528
    • 0.5 u: 2203
    • 1.0 u: 1662
• zone 4:
  • 0.3 u: 1080
  • 0.5 u: 415
  • 1.0 u: 332

cleaning cleanroom and particle count

• 5:10 pm: ran zero count test on particle counter
• 5:14 pm: started particle count

  NOTE: initial counts are significantly above allowed limit. ~10 times larger than ISO class 5 standard in the smallest size range. Realized partway through ceiling tile changes that the power/lights for some of the hepa fans in the ceiling frame had been turned off. May explain this high number. Have since turned fans back back on.

  • zone 3:
    • 0.3 u: 109208
    • 0.5 u: 16337
    • 1.0 u: 581
• zone 4:
  • 0.3 u: 51340
  • 0.5 u: 9228
  • 1.0 u: 581
• 5:33 pm: started replacing ceiling tiles
• 6:25 pm: began surface check and wipedown, including softwalls
• 6:33 pm: started vacuuming the floor
• 6:45 pm: finished vacuuming the floor
• 6:45 pm: started mopping the floor
• 6:50 pm: finished mopping the floor
• 6:52 pm: started cleaning the buckets
• 6:53 pm: started mopping with IPA wipes
• 6:58 pm: finished mopping with IPA wipes
• 6:59 pm: changed sticky floor mats
• 7:00 pm: started particle count
  • zone 3:
    • 0.3 u: 5404
    • 0.5 u: 1413
    • 1.0 u: 41
• zone 4:
  • 0.3 u: 1704
  • 0.5 u: 332
  • 1.0 u: 166

The replacement door for the HEPA garment cabinet arrived last week, and was installed on Thursday. However, it looks like there's a small gap between the door and where the hinge is attached to the cabinet frame. No screws were provided with the replacement door. If we want to perform any adjustments, we have to be very careful; the screws break very easily.

cleaning cleanroom and particle count

• 11:50 am: ran zero count test on particle counter
• 11:55 am: started particle count
  • zone 3:
    • 0.3 u: 1787
    • 0.5 u: 581
    • 1.0 u: 166
• zone 4:
  • 0.3 u: 623
  • 0.5 u: 290
  • 1.0 u: 124
• 12:17 pm: began surface check and wipedown, including softwalls
• 12:25 pm: started vacuuming the floor
• 12:36 pm: finished vacuuming the floor
• 12:44 pm: started mopping the floor
• 12:57 pm: finished mopping the floor
• 12:58 pm: started cleaning the buckets
• 12:59 pm: started mopping with IPA wipes
• 1:05 pm: finished mopping with IPA wipes
• 1:06 pm: changed sticky floor mats
• 1:08 pm: started particle count
  • zone 3:
    • 0.3 u: 1621
    • 0.5 u: 581
    • 1.0 u: 332
• zone 4:
  • 0.3 u: 1080
  • 0.5 u: 457
  • 1.0 u: 249

cleaning cleanroom and particle count

NOTE: particle counter was found dead, with the charging dock unplugged. For future reference, if you need to unplug the dock, please either plug it back in when you're done, or make a note in an elog so someone else can come down and charge it.

• 1:07 pm: ran zero count test on particle counter
• 1:26 pm: started particle count
  • zone 3:
    • 0.3 u:1787
    • 0.5 u:457
    • 1.0 u:41
• zone 4: We were only able to charge the particle counter a small amount before starting the cleaning, so it died again halfway through this measurement, and we didn't get results for zone 4. In interest of time, we just put it on the charger and started the cleaning.
• 1:49 pm: began surface check and wipedown, including softwalls
• 2:16 pm: started vacuuming the floor
• 2:24 pm: finished vacuuming the floor
• 2:26 pm: started mopping the floor
• 2:32 pm: finished mopping the floor
• 2:32 pm: started cleaning the buckets
• 2:35 pm: started mopping with IPA wipes
• 2:43 pm: finished mopping with IPA wipes
• 2:43 pm: changed sticky floor mats
• 2:45 pm: started particle count
  • zone 3:
    • 0.3 u: 1288
    • 0.5 u: 124
    • 1.0 u: 0
• zone 4:
  • 0.3 u: 415
  • 0.5 u: 290
  • 1.0 u: 0

cleaning cleanroom and particle count

• 1:45 pm: ran zero count test on particle counter
• 1:50 pm: started particle count
  • zone 3:
    • 0.3 u: 2660
    • 0.5 u: 332
    • 1.0 u: 41
• zone 4:
  • 0.3 u: 8106
  • 0.5 u: 2494
  • 1.0 u: 831
• 2:08 pm: began surface check and wipedown, including softwalls
• 2:22 pm: started vacuuming the floor
• 2:39 pm: finished vacuuming the floor
• 2:43 pm: started mopping the floor
• 2:53 pm: finished mopping the floor
• 2:54 pm: started cleaning the buckets
• 2:59 pm: started mopping with IPA wipes
• 3:06 pm: finished mopping with IPA wipes
• 3:10 pm: changed sticky floor mats
• 3:06 pm: started particle count
  • zone 3:
    • 0.3 u: 1496
    • 0.5 u: 83
    • 1.0 u: 0
• zone 4:
  • 0.3 u: 789
  • 0.5 u: 83
  • 1.0 u: 41

cleaning cleanroom and particle count

• 10:45 am: ran zero count test on particle counter
• 11:02 am: started particle count
  • zone 3:
    • 0.3 u: 3284
    • 0.5 u: 1247
    • 1.0 u:332
• zone 4:
  • 0.3 u: 1829
  • 0.5 u: 581
  • 1.0 u: 207
• 11:15 am: began hepavac of rest of lab
• 11:19 am: began surface check and wipedown, including softwalls
• 11:32 am: finished hepavac of rest of lab
• 11:35 am: started vacuuming the cleanroom floor
• 11:45 am: finished vacuuming the floor
• 11:47 am: started mopping the floor
• 11:55 am: finished mopping the floor
• 11:56 am: started cleaning the buckets
• 11:57 am: started mopping with IPA wipes
• 12:02 pm: finished mopping with IPA wipes
• 12:03 pm: changed sticky floor mats
• 12:04 pm: started particle count
  • zone 3:
    • 0.3 u: 3117
    • 0.5 u: 374
    • 1.0 u: 124
• zone 4:
  • 0.3 u: 4531
  • 0.5 u: 540
  • 1.0 u: 0

We moved Frosti into the cleanroom and debugged it to make sure everything was working. One of the DB25 pins broke off at the connector for element 1 so it needed to be recrimped. Element 6 short circuited but fixed with adjustment to the heater power pin position. We connected the power and sensor connectors to the power box and recalibrated the RTD sensors.

I have begun moving parts into the cleanroom for the upcoming FROSTI RIN tests that will be conducted within the next few weeks. While waiting for the rest of the equipment to arrive to perform the full-scale tests, I have additionally moved the FROSTI under the shelf above the optical table, where it will stay for the meantime. As always, please use caution when in the cleanroom. Aside from the FROSTI, the IR photodetectors that will be used for the test are delicate and costly to replace.

For some preliminary tests, I moved the IR photodetectors outside of the cleanroom and onto the other optical table. The basic goal was to obtain a signal from both photodetectors. To achieve this, one of the heater cartridges used for early FLIR measurements months ago was hooked up to a power supply (PS). The PS was set to supply 0.20 A with a voltage of 2.8 V; the corresponding power is thus 0.56 W. With this, I was able to measure a signal using the Red Pitaya, the device that will be used for following RIN measurements.

cleaning cleanroom and particle count

• 12:25 pm: started particle count
  • zone 3:
    • 0.3 u: 4614
    • 0.5 u: 872
    • 1.0 u:83
• zone 4:
  • 0.3 u: 2411
  • 0.5 u: 415
  • 1.0 u: 83
• 12:48 pm: began surface check and wipedown, including softwalls
• 1:20 pm: started vacuuming the floor
• 1:30 pm: finished vacuuming the floor
• 1:34 pm: started mopping the floor
• 1:40 pm: finished mopping the floor
• 1:40 pm: started cleaning the buckets
• 1:42 pm: started mopping with IPA wipes
• 1:50 pm: finished mopping with IPA wipes
• 1:51 pm: changed sticky floor mats
• 3:44 pm: started particle count
  • zone 3:
    • 0.3 u: 3207
    • 0.5 u: 624
    • 1.0 u: 83
• zone 4:
  • 0.3 u: 916
  • 0.5 u: 83
  • 1.0 u: 0

[Luke, Luis, Michael]

cleaning cleanroom and particle count

• 8:30 am: started particle count
  • zone 3:
    • 0.3 u: 1195
    • 0.5 u: 177
    • 1.0 u: 132
• zone 4:
  • 0.3 u: 619
  • 0.5 u: 0
  • 1.0 u: 0
• 9:00 am: began surface check and wipedown, including softwalls
• 9:35 am: started vacuuming the floor
• 9:43 am: finished vacuuming the floor
• 9:45 am: started mopping the floor
• 9:55 am: finished mopping the floor
• 9:56 am: started cleaning the buckets
• 10:00 am: started mopping with IPA wipes
• 10:05 am: finished mopping with IPA wipes
• 10:20m: started particle count
  • zone 3:
    • 0.3 u: 2213
    • 0.5 u: 398
    • 1.0 u: 0
• zone 4:
  • 0.3 u: 1150
  • 0.5 u: 177
  • 1.0 u: 44

[Luke, Tyler, Cynthia, Shane, Michael]

Summary of Cleaning Activities:

We began cleaning Room 1119 at 2:00 PM.

At 2:30 PM, we moved to Room 1129 and continued cleaning.

Cleaning tasks included wiping down dust-collecting surfaces and vacuuming the floors.

Once the labs were clean, we proceeded to the cleanroom. 

• Wiping down surfaces and soft walls
• Vacuuming, mopping the floor, and finishing with IPA wipes

Particle Count Measurements:

• Pre-cleaning (2:30 PM):
  • Zone 3:
    • 0.3 µm: 973
    • 0.5 µm: 354
    • 1.0 µm: 132
  • Zone 4:
    • 0.3 µm: 486
    • 0.5 µm: 177
    • 1.0 µm: 0
• Post-cleaning (4:10 PM):
  • Zone 3:
    • 0.3 µm: 619
    • 0.5 µm: 132
    • 1.0 µm: 0
  • Zone 4:
    • 0.3 µm: 397
    • 0.5 µm: 0
    • 1.0 µm: 0

[Luke, Mary, Luis]

Particle Count Measurements:

• Pre-cleaning (8:40 am):
  • Zone 3:
    • 0.3 µm: 441
    • 0.5 µm: 44
    • 1.0 µm: 0
  • Zone 4:
    • 0.3 µm: 353
    • 0.5 µm: 176
    • 1.0 µm: 44

• Started Cleaning (3:16 pm)
• Finished Cleaning (4:10 pm)

• Post-cleaning (4:15 pm):
  • Zone 3:
    • 0.3 µm: 574
    • 0.5 µm: 265
    • 1.0 µm: 132
  • Zone 4:
    • 0.3 µm: 177
    • 0.5 µm: 44
    • 1.0 µm: 0

[Luke, Mohak, Luis]

We were also able to remove the residue that has built up on the soft walls by donning a skinny bunny suit and with two wipes rubbing both sides of the soft walls at the same time. The wipes would get gummy very quickly and need to be replaced frequently.

Particle Count Measurements:

• Pre-cleaning (1:20 pm):
  • Zone 3:
    • 0.3 µm: 3577
    • 0.5 µm: 1369
    • 1.0 µm: 485
  • Zone 4:
    • 0.3 µm: 1062
    • 0.5 µm: 442
    • 1.0 µm: 177

• Started Cleaning (3:00 pm)
• Finished Cleaning (4:00 pm)

• Post-cleaning (4:22 pm):
  • Zone 3:
    • 0.3 µm: 3577
    • 0.5 µm: 618
    • 1.0 µm: 132
  • Zone 4:
    • 0.3 µm: 2031
    • 0.5 µm: 397
    • 1.0 µm: 132

Date and Time: Around 2:20 PM on May 21, 2025

Location and Temperature:

• Back of the room, around the working station: 85.5 °F
• Front of the room, around the doorway: 82.3 °F

[Luke, Luis, Tyler, Ma, Christina, Maple]

We started by cleaning outside of the cleanroom wiping down the cable channel and working our way down. We replaced the air filter in the HEPA filter with what seemed to be the last one in storage. We then vacuumed outside, before wiping down the inside of the cleanroom. We then vacuumed, mopped, and wiped down the floor inside the cleanroom.

We are ready for venting the vacuum chamber which is planned to take place 6/26/25 at 10am. 

Particle Count Measurements:

• Pre-cleaning (12:00 pm):
  • Zone 3:
    • 0.3 µm: 2517
    • 0.5 µm: 662
    • 1.0 µm: 176
  • Zone 4:
    • 0.3 µm: 177
    • 0.5 µm: 44
    • 1.0 µm: 0

• Post-cleaning (1:45 pm):
  • Zone 3:
    • 0.3 µm: 619
    • 0.5 µm: 88
    • 1.0 µm: 0
  • Zone 4:
    • 0.3 µm: 177
    • 0.5 µm: 88
    • 1.0 µm: 0

[Luke, Luis]

We’ve been looking into methods for evaluating the performance of the HEPA filters in the clean room. Measuring flow rate appears to be a promising approach, since the filter manual specifies a recommended minimum of 70 ft/min.

At the moment, we don’t have a flow rate measurement device on hand. We're currently looking into two options:

• A standard vane-style anemometer, which is more affordable but may lack sensitivity near the minimum required flow rate.
• A hot-wire anemometer, which offers better resolution and accuracy at lower speeds, though it's more expensive.

In the next few days, either Luis or I will contact Terra Universal to see if they have any measurement solutions that would integrate well with our clean room setup, or if they can recommend best practices for verifying HEPA performance.

[Pooyan, Ma, Mary, Tyler]

While re-installing the clean-room HEPA fan filters, we realized that one of the blowers is broken. The issue seems to be that the plastic damper bracket that is keeping the blower in place has failed. The fix is to open up the fan unit, and replace the broken vibration damper. We installed the defected unit on top of the clean room entrance, for easy future access.

• concrete Caulk to fill the drill holes in 1119
  • Example [Pooyan: I have a caulk gun and silicon caulk at home, if needed.]
• Water hose for the washer in 1125
  • 1/2" diameter
  • almost 8 Ft 
• Exhaust for the oven in 1125
  • Question: not sure which way we want the exhaust to go. Measurements depend on the path. 
  • Oven exhaust to the ceiling vertical distance: 47"
  • Oven exhaust to the ceiling exhaust distance: 6 ft
• Rubber vibration dampers for the cleanroom fans (see the first 4 pictures)
  • 25 mm diameter, 13 mm height, ~5-6 mm thread, 6 mm deep
  • Example (This is the male version. We need one with female on both sides)
• Cabling conduit from the cable tray to the optical table frame (through the cleanroom ceiling)
  • Aluminum example
  • Galvanized Steel example 
• Wire cable tray for 1125
  • ~10 Ft, exactly similar to the one already installed in 1129

[Ma, Mary, Tyler, Pooyan]

HEPA fan air flow measurements are done with the fans sitting on their side in the lab, and the anemometer being 24in away from the filter face of the fan. Per company's documents, we need to replace the filter if the air flow velocity drops under 38-45 fpm for the medium settings.)
 

All numbers are in fpm unit. The measurement for each unit is done twice in front of the fan positions.  

[Ma, Cece, Pooyan, Tyler]

We installed the repaired HEPA fans on top of the cleanroom, and cleaned the fans themselves. The table of all the Serial Numbers for the fans, filters, and where they are installed is added for the record. 

The electrical wiring diagram of the cleanroom is on page (1) of the attached file.

• Blue lines are protected by the lab UPS, and power the power strips attached to the frame of the optical tables. The same power strips feed the frame lights and the vacuum system. 
• Red lines are connected to the red outlet on the celling cable tray, presumabaly connected to the building's backup system. The feed everything on the ceiling of the cleanroom by first going through two switches attached to the frame of the clean room. Each outlet feeds two fans and one ceiling lamp via power strips sitting on top of the cleanroom ceiling. (see pictures on page (2))

We will need two sets of conduits feeding cables into the cleanroom, possibly secured on the legs of the cleanroom frame and going through the ceiling tile.

• The eastern conduit will have all of the connection/control/CyMAC cables, and two power cables. (See page (3))
• The western conduit will have two power cables, and the table's air feeder. 
• I suggest that each conduit be either a two inch wide, or two one inch wide coduits. Anything less than one inch wide will not be able to contain the current batch of chables. 

Page 4 is a possible cartoon of where we want to install the conduits. We can have electric boxes either on the both sides of the conduit, or just on one side.